Metal Detector Rain Covers: How to Protect a Non-Waterproof Control Box
Plenty of good detectors are not waterproof. They handle damp grass and a light drizzle, but a proper shower can get into the control box, the battery compartment or the headphone jack. Since some of the best field hunting happens after rain, it is worth knowing how to keep water out and what to do if some gets in.
Know your detector's rating
Manufacturers use a range of terms, and they mean different things:
| Term | What it usually means |
|---|---|
| Not water resistant | Keep dry. Even light rain should be covered. |
| Weatherproof / rainproof | Handles rain and splashes, not submersion. |
| Waterproof coil only | Coil can go in water; control box must stay dry. |
| Waterproof to a stated depth | Submersible to that depth, under the conditions in the manual. |
| IP rating (such as IP68) | A standard rating; the manufacturer's notes say exactly what it covers. |
Even waterproof detectors may have exceptions, such as needing waterproof headphones or a sealed connector cap. Read the manual section on water before trusting any label.
Where water gets in
- The control box seams and display. Rain runs down and finds gaps.
- The battery compartment. Doors with worn seals or no seals are a common entry point.
- The headphone jack. Open jacks fill with water easily, especially when facing up.
- External coil connectors. The plug and socket on detectors with external cables.
- Charging ports. USB or charging sockets, especially if a cap is missing.
- Speaker grilles. On some boxes, these let water reach the electronics.
Control box covers
A fitted cover is the main defense. Most are made of vinyl, neoprene or a soft plastic, with a clear window over the display. Good ones:
- Fit your model snugly, with cutouts or flexible areas for buttons.
- Have a clear, scratch-resistant window over the screen.
- Leave a path for the headphone cable and coil cable without big gaps.
- Drain or breathe enough that condensation does not pool inside.
Model-specific covers are available for many popular detectors, from the manufacturer and from third parties. Generic covers can work but tend to be baggier. You can browse control box rain covers on Amazon; check that the listing names your detector.
Sealing the weak points
Headphone jack
If you use wired headphones, make sure the plug is fully seated; that blocks most of the jack. If you are not using headphones, a rubber jack plug or dust cap keeps water out. Point the jack downward if the box design allows. Wireless headphones avoid the issue if your detector supports them, though the transmitter or module may have its own water limits.
Battery door
Check the seal or gasket for cracks and dirt. Close the door firmly. Never open it in the rain. If the door has no seal, a cover over the whole box is your best protection.
Coil connector
Make sure the connector is screwed in fully and the collar is tight. Some people wrap a strip of self-amalgamating tape over the joint in wet conditions. Remove it after so moisture is not trapped against the metal.
Charging ports
Keep port caps closed. If a cap is missing, ask the manufacturer for a replacement.
Your clothes and kit
Staying dry yourself helps your detector stay dry, because wet sleeves drip onto the box. A rain jacket with sleeves that seal at the wrist, a brimmed hat and waterproof gloves all help. Keep your pinpointer in a holster rather than a pocket that fills with water, and use a small dry bag for your phone and spare batteries.
Wired headphones can carry water down the cable into the jack. Route the cable so it loops down before reaching the box, which lets drips fall off instead of running into the socket.
When to call it a day
A cover helps with drizzle and showers. It is not a license to hunt in a downpour with a non-waterproof machine. Stop if:
- Rain is heavy enough that water is pooling on the cover.
- The detector starts behaving oddly: falsing, display glitches, sound dropouts.
- You see condensation inside the screen.
- There is lightning nearby. Holding a long shaft in an open field is a bad idea in a thunderstorm; follow standard lightning safety and get indoors.
Drying out after a wet hunt
- Wipe the outside dry before opening anything.
- Remove the cover and let it dry separately.
- Remove batteries if they are accessible and not sealed in.
- Open the battery door and port caps indoors and leave them open to air dry.
- Disconnect the coil on detectors with external cables, and let the connector dry.
- Dry at room temperature. Avoid ovens, radiators and hot hair dryers, which can damage plastics and seals.
- Test before your next hunt. If anything seems off, contact the manufacturer.
Bringing a cold, wet detector into a warm house can also cause condensation inside. Let it warm up gradually, ideally still in its bag. See detector condensation from a cold car for more.
If water got inside
If you suspect water inside the control box, turn it off and do not turn it back on to "check" until it has dried thoroughly. Remove batteries. Let it sit somewhere warm and dry with good airflow. Some people put the unit in a box with desiccant packs; that is reasonable, though it is no substitute for time.
Wet weather kit checklist
- Fitted control box cover with a clear window
- Jack plug or wired headphones that seal the socket
- Self-amalgamating tape for the coil connector
- Rain jacket, brimmed hat, waterproof gloves
- Dry bag for phone and spares
- Towel in the car for drying gear before you pack it
FAQ
Can I use a plastic bag as a detector rain cover?
In an emergency, a clear plastic bag over the control box, secured loosely, is better than nothing. It can trap condensation and make buttons hard to use, so a fitted cover is better for regular use.
Is it safe to detect in light rain with a non-waterproof detector?
Many detectors cope with light drizzle, especially with a cover, but it depends on the model. Check what the manufacturer says, protect the box and jacks, and stop if the rain gets heavy.
What should I do if water got into my detector?
Turn it off, remove batteries if accessible, and let it dry slowly at room temperature with any covers open. Avoid hair dryers on hot settings or ovens. If it behaves oddly afterward, contact the manufacturer or an authorized service center.
Do I need to cover the coil?
Most search coils are sealed and fine in wet grass and rain, and many are waterproof even on detectors with non-waterproof control boxes. Check your manual. A coil cover protects against scuffs, not water.
The bottom line
A non-waterproof detector can still go out after the rain if you protect the weak points. Learn your model's rating, fit a control box cover, seal the jacks and battery door, and dry everything slowly afterward. If heavy rain sets in, put the detector away and come back when it eases. For more on what waterproof ratings mean, see waterproof metal detectors explained.